u-boot引导内核（kernel.org下载）停在：Starting kernel ...

kangear

U-Boot 1.3.4 (Oct  8 2012 - 23:15:30) for SMDKV210

CPU:  S5PV210@1000MHz(OK)

        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz

        MPLL = 667MHz, EPLL = 96MHz

                       HclkDsys = 166MHz, PclkDsys = 83MHz

                       HclkPsys = 133MHz, PclkPsys = 66MHz

                       SCLKA2M  = 200MHz

Serial = CLKUART

Board:   X210

DRAM:    512 MB

after init sequence,gd->bd->bi_boot_params:30000100

Flash:   8 MB

SD/MMC: Card init fail!

0 MB

NAND:    512 MB

In:      serial

Out:     serial

Err:     serial

checking mode for fastboot ...

Hit any key to stop autoboot:  0

x210 # bdinfo  

arch_number = 0x00000998

env_t       = 0x00000000

boot_params = 0x30000100

DRAM bank   = 0x00000000

-> start    = 0x30000000

-> size     = 0x10000000

DRAM bank   = 0x00000001

-> start    = 0x40000000

-> size     = 0x10000000

ethaddr     = 00:40:5C:26:0A:5B

ip_addr     = 192.168.0.103

baudrate    = 115200 bps

x210 # setenv machid 0x999;saveenv;

Saving Environment to SMDK bootable device...

Erasing Nand...

Writing to Nand...

Saved enviroment variables

x210 # reset

reset...

OK

U-Boot 1.3.4 (Oct  8 2012 - 23:15:30) for SMDKV210

CPU:  S5PV210@1000MHz(OK)

        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz

        MPLL = 667MHz, EPLL = 96MHz

                       HclkDsys = 166MHz, PclkDsys = 83MHz

                       HclkPsys = 133MHz, PclkPsys = 66MHz

                       SCLKA2M  = 200MHz

Serial = CLKUART

Board:   X210

DRAM:    512 MB

after init sequence,gd->bd->bi_boot_params:30000100

Flash:   8 MB

SD/MMC: Card init fail!

0 MB

NAND:    512 MB

In:      serial

Out:     serial

Err:     serial

checking mode for fastboot ...

Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x600000, size 0x500000

Main area read (40 blocks):

5242880 bytes read: OK

Boot with zImage

In bootm linux!!!

cmdline:console=ttySAC0,115200 root=/dev/mtdblock4 rw init=/linuxrc rootfstype=jffs2

Using machid 0x999 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

（说明：bdinfo是查询U-BOOT目前机器码（arch_number = 0x00000998）即为10进制 2456

；setenv machid 0x999 是改变机器码；reset 重新引导 ）

这时可以看到Using machid 0x999 from environment

已经用0x999的机器码来引导内核了，果不其然失败。打印信息如下：

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

衬托完了，我要说我的问题了，我在kernel.org下载的Linux-2.6.35.7用s5pv210_defconfig来配置，它的机器码也是 0x998，修改debug串口为0。可是我编译过后，用提供的u-boot来进行引导时打印信息为：

U-Boot 1.3.4 (Oct  8 2012 - 23:15:30) for SMDKV210

CPU:  S5PV210@1000MHz(OK)

        APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz

        MPLL = 667MHz, EPLL = 96MHz

                       HclkDsys = 166MHz, PclkDsys = 83MHz

                       HclkPsys = 133MHz, PclkPsys = 66MHz

                       SCLKA2M  = 200MHz

Serial = CLKUART

Board:   X210

DRAM:    512 MB

after init sequence,gd->bd->bi_boot_params:30000100

Flash:   8 MB

SD/MMC: Card init fail!

0 MB

NAND:    512 MB

In:      serial

Out:     serial

Err:     serial

checking mode for fastboot ...

Hit any key to stop autoboot:  0

x210 # bdinfo

arch_number = 0x00000998

env_t       = 0x00000000

boot_params = 0x30000100

DRAM bank   = 0x00000000

-> start    = 0x30000000

-> size     = 0x10000000

DRAM bank   = 0x00000001

-> start    = 0x40000000

-> size     = 0x10000000

ethaddr     = 00:40:5C:26:0A:5B

ip_addr     = 192.168.0.103

baudrate    = 115200 bps

x210 # boot

NAND read: device 0 offset 0x600000, size 0x500000

Main area read (40 blocks):

5242880 bytes read: OK

Boot with zImage

In bootm linux!!!

cmdline:console=ttySAC0,115200 root=/dev/mtdblock4 rw init=/linuxrc rootfstype=jffs2

Using machid 0x998 from environment

Starting kernel ...

连Uncompressing Linux... done, booting the kernel.都没有，x210ii提供的内核是不是映像进行加工？我缺了哪些东西？