x4412&ibox项目实战4－在uboot中添加开机LOGO

armeasy · 发表于 2014-9-20 17:57:43

在uboot中添加开机LOGO，基本上可以归纳为以下四个步骤：

一：初始化LCD控制器相应的寄存器；

二：初始化LCD控制器对应的时钟源；

三：填充framebuffer；

四：打开背光。

在uboot\board\samsung\x4412\x4412.c中，我们在函数board_late_init中添加显示开机LOGO的函数x4412_framebuffer_init()，该函数内嵌了多个函数，他们完成了以上所有步骤。其源码如下：

void x4412_framebuffer_init(void)
{
exynos4412_clk_initial(); //初始化时钟
exynos4412_fb_initial(); //初始化LCD寄存器
}

复制代码

这里前两个函数用于设置时钟相关寄存器：

void exynos4412_clk_initial(void)
{
/* Modify LCD clk */
writel(EXYNOS4412_CLK_SRC_LCD, (readl(EXYNOS4412_CLK_SRC_LCD) & ~(0xf<<0)) | (0x6<<0));
writel(EXYNOS4412_CLK_DIV_LCD, (readl(EXYNOS4412_CLK_DIV_LCD) & ~(0xf<<0)) | (0x0<<0));
exynos4412_setup_clocks(24 * 1000 * 1000);
}

复制代码

整个时钟的配置，在exynos4412-clk.c中。时钟配置完后，我们再来看LCD寄存器初始化函数exynos4412_fb_initial()。

void exynos4412_fb_initial()
{
struct exynos4412_fb_data_t * dat;
dat = &vs070cxn;
if( (dat->bits_per_pixel != 16) && (dat->bits_per_pixel != 24) && (dat->bits_per_pixel != 32) )
return;
exynos4412_fb.dat = dat;
exynos4412_fb.surface.info.bits_per_pixel = dat->bits_per_pixel;
exynos4412_fb.surface.info.bytes_per_pixel = dat->bytes_per_pixel;
exynos4412_fb.surface.info.red_mask_size = dat->rgba.r_mask;
exynos4412_fb.surface.info.red_field_pos = dat->rgba.r_field;
exynos4412_fb.surface.info.green_mask_size = dat->rgba.g_mask;
exynos4412_fb.surface.info.green_field_pos = dat->rgba.g_field;
exynos4412_fb.surface.info.blue_mask_size = dat->rgba.b_mask;
exynos4412_fb.surface.info.blue_field_pos = dat->rgba.b_field;
exynos4412_fb.surface.info.alpha_mask_size = dat->rgba.a_mask;
exynos4412_fb.surface.info.alpha_field_pos = dat->rgba.a_field;
exynos4412_fb.surface.info.fmt = get_pixel_format(&(exynos4412_fb.surface.info));
exynos4412_fb.surface.w = dat->width;
exynos4412_fb.surface.h = dat->height;
exynos4412_fb.surface.pitch = dat->width * dat->bytes_per_pixel;
exynos4412_fb.surface.flag = SURFACE_PIXELS_DONTFREE;
exynos4412_fb.surface.pixels = dat->vram_front;
exynos4412_fb.surface.clip.x = 0;
exynos4412_fb.surface.clip.y = 0;
exynos4412_fb.surface.clip.w = dat->width;
exynos4412_fb.surface.clip.h = dat->height;
memset(&exynos4412_fb.surface.maps, 0, sizeof(struct surface_maps));
surface_set_maps(&exynos4412_fb.surface.maps);
fb_init(&exynos4412_fb);
exynos4412_display_logo();
if(dat->backlight)
dat->backlight(255);
}

复制代码

以上函数基本上都在填充结构体，这里vs070cxn结构体描述了LCD屏的前后肩等相关参数，不同的屏参数不一样。通常，更换不同的屏，主要也就是修改这个结构体的相关参数。

static struct exynos4412_fb_data_t vs070cxn = {
.regbase = EXYNOS4412_LCD_BASE,
.width = 1024,
.height = 600,
.bits_per_pixel = 32,
.bytes_per_pixel = 4,
.freq = 60,
.output = EXYNOS4412_FB_OUTPUT_RGB,
.rgb_mode = EXYNOS4412_FB_MODE_BGR_P,
.bpp_mode = EXYNOS4412_FB_BPP_MODE_32BPP,
.swap = EXYNOS4412_FB_SWAP_WORD,
.rgba = {
.r_mask = 8,
.r_field = 0,
.g_mask = 8,
.g_field = 8,
.b_mask = 8,
.b_field = 16,
.a_mask = 8,
.a_field = 24,
},
.timing = {
.h_fp = 160,
.h_bp = 140,
.h_sw = 20,
.v_fp = 12,
.v_fpe = 1,
.v_bp = 20,
.v_bpe = 1,
.v_sw = 3,
},
.polarity = {
.rise_vclk = 0,
.inv_hsync = 1,
.inv_vsync = 1,
.inv_vden = 0,
},
.vram_front = &vram[0][0],
.vram_back = &vram[1][0],
.init = lcd_init,
.backlight = lcd_backlight,
};

复制代码

在fb_init()函数中，初始化了一堆LCD相关寄存器：

static void fb_init(struct fb_t * fb)
{
struct exynos4412_fb_data_t * dat = (struct exynos4412_fb_data_t *)(fb->dat);
/*
* Initial lcd port
*/
writel(EXYNOS4412_GPF0_BASE + EXYNOS4412_GPIO_CON, 0x22222222);
writel(EXYNOS4412_GPF0_BASE + EXYNOS4412_GPIO_DRV, 0xffffffff);
writel(EXYNOS4412_GPF0_BASE + EXYNOS4412_GPIO_PUD, 0x0);
writel(EXYNOS4412_GPF1_BASE + EXYNOS4412_GPIO_CON, 0x22222222);
writel(EXYNOS4412_GPF1_BASE + EXYNOS4412_GPIO_DRV, 0xffffffff);
writel(EXYNOS4412_GPF1_BASE + EXYNOS4412_GPIO_PUD, 0x0);
writel(EXYNOS4412_GPF2_BASE + EXYNOS4412_GPIO_CON, 0x22222222);
writel(EXYNOS4412_GPF2_BASE + EXYNOS4412_GPIO_DRV, 0xffffffff);
writel(EXYNOS4412_GPF2_BASE + EXYNOS4412_GPIO_PUD, 0x0);
writel(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_CON, (readl(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_CON) & ~(0xffff<<0)) | (0x2222<<0));
writel(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_DRV, (readl(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_DRV) & ~(0xff<<0)) | (0xff<<0));
writel(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_PUD, (readl(EXYNOS4412_GPF3_BASE + EXYNOS4412_GPIO_PUD) & ~(0xff<<0)) | (0x00<<0));
/*
* Lcd init function
*/
if(dat->init)
dat->init();
/*
* Display path selection
*/
writel(EXYNOS4412_LCDBLK_CFG, (readl(EXYNOS4412_LCDBLK_CFG) & ~(0x3<<0)) | (0x2<<0));
writel(EXYNOS4412_LCDBLK_CFG2, (readl(EXYNOS4412_LCDBLK_CFG2) & ~(0x1<<0)) | (0x1<<0));
/*
* Turn off all windows
*/
writel(dat->regbase + WINCON0, (readl(dat->regbase + WINCON0) & ~0x1));
writel(dat->regbase + WINCON1, (readl(dat->regbase + WINCON1) & ~0x1));
writel(dat->regbase + WINCON2, (readl(dat->regbase + WINCON2) & ~0x1));
writel(dat->regbase + WINCON3, (readl(dat->regbase + WINCON3) & ~0x1));
writel(dat->regbase + WINCON4, (readl(dat->regbase + WINCON4) & ~0x1));
/*
* Turn off all windows color map
*/
writel(dat->regbase + WIN0MAP, (readl(dat->regbase + WIN0MAP) & ~(1<<24)));
writel(dat->regbase + WIN1MAP, (readl(dat->regbase + WIN1MAP) & ~(1<<24)));
writel(dat->regbase + WIN2MAP, (readl(dat->regbase + WIN2MAP) & ~(1<<24)));
writel(dat->regbase + WIN3MAP, (readl(dat->regbase + WIN3MAP) & ~(1<<24)));
writel(dat->regbase + WIN4MAP, (readl(dat->regbase + WIN4MAP) & ~(1<<24)));
/*
* Turn off all windows color key and blending
*/
writel(dat->regbase + W1KEYCON0, (readl(dat->regbase + W1KEYCON0) & ~(3<<25)));
writel(dat->regbase + W2KEYCON0, (readl(dat->regbase + W2KEYCON0) & ~(3<<25)));
writel(dat->regbase + W3KEYCON0, (readl(dat->regbase + W3KEYCON0) & ~(3<<25)));
writel(dat->regbase + W4KEYCON0, (readl(dat->regbase + W4KEYCON0) & ~(3<<25)));
/*
* Initial lcd controller
*/
exynos4412_fb_set_output(dat);
exynos4412_fb_set_display_mode(dat);
exynos4412_fb_display_off(dat);
exynos4412_fb_set_polarity(dat);
exynos4412_fb_set_timing(dat);
exynos4412_fb_set_lcd_size(dat);
exynos4412_fb_set_clock(dat);
/*
* Set lcd video buffer
*/
exynos4412_fb_set_buffer_size(dat, 0);
exynos4412_fb_set_window_position(dat, 0);
exynos4412_fb_set_window_size(dat, 0);
/*
* Enable window 0 for main display area
*/
exynos4412_fb_window0_enable(dat);
/*
* Display on
*/
exynos4412_fb_display_on(dat);
/*
* Wait a moment
*/
// mdelay(100);
}

复制代码

紧接着，调用exynos4412_display_logo函数填充framebuffer。

static void exynos4412_display_logo(void)
{
struct surface_t * screen = exynos4412_screen_surface();
struct surface_t * logo;
struct rect_t rect;
u32_t c;
exynos4412_screen_flush();
c = surface_map_color(screen, get_named_color("greenyellow"));
surface_fill(screen, &screen->clip, c, BLEND_MODE_REPLACE);
disp_hanzi();
lcd_print(450, 350, 0x00000000, c, "www.9tripod.com");
}

复制代码

这里填充framebuffer，引用了x4412开发板配套的裸机源码，里面引用了一套绘图机制，我们利用它可以很方便的在LCD上打印字符，输出图片等。这里我们同样引用了裸机里面的汉字显示实验，调用了disp_hanzi函数，在LCD屏上显示几个楷体汉字，同时调用lcd_print函数在汉字下面打印了一串字符串。

到这里，其实图形已经显示在LCD上了，我们只需打开背光即可看到界面了。在exynos4412_fb_initial函数中，通过回调函数调用了lcd_backlight函数：

static void lcd_backlight(u8_t brightness)
{
if(brightness)
{
writel(EXYNOS4412_GPD0_BASE + EXYNOS4412_GPIO_DAT, (readl(EXYNOS4412_GPD0_BASE + EXYNOS4412_GPIO_DAT) & ~(0x1<<0)) | (0x0<<0));
writel(EXYNOS4412_GPX3_BASE + EXYNOS4412_GPIO_DAT, (readl(EXYNOS4412_GPX3_BASE + EXYNOS4412_GPIO_DAT) & ~(0x1<<5)) | (0x1<<5));
}
else
{
writel(EXYNOS4412_GPD0_BASE + EXYNOS4412_GPIO_DAT, (readl(EXYNOS4412_GPD0_BASE + EXYNOS4412_GPIO_DAT) & ~(0x1<<0)) | (0x1<<0));
writel(EXYNOS4412_GPX3_BASE + EXYNOS4412_GPIO_DAT, (readl(EXYNOS4412_GPX3_BASE + EXYNOS4412_GPIO_DAT) & ~(0x1<<5)) | (0x0<<5));
}
}

复制代码

这里通过GPIO口打开背光驱动IC，从而点亮背光。到此，uboot的开机LOGO真实的呈现在我们面前了。

附上本文的uboot映像，有兴趣的朋友可以测试下：

游客，如果您要查看本帖隐藏内容请回复

yangyunlong · 发表于 2014-9-20 19:21:51

学习了，牛。

hardjet · 发表于 2014-9-22 22:06:59

这个牛~~~

zgkxzx · 发表于 2014-9-24 17:12:21

很好，写的很好！

wangkai9531 · 发表于 2014-10-11 11:03:03

很适合~~~~~~~~~~~~

guitou · 发表于 2014-10-18 09:53:17

学习下下～～～

leishasha · 发表于 2014-10-18 11:42:46

挺好的，很详细

guitou · 发表于 2014-10-18 16:38:27

请问下楼主：static struct exynos4412_fb_data_t结构体在哪里定义。是不是我这开发板配的源码版本不同？不存在uboot\board\samsung\x4412\这个文件夹。

zhengxi · 发表于 2014-10-22 16:50:41

好好看看，代码在哪里

tootwo · 发表于 2014-10-24 11:36:38

有源码吗？

valeev · 发表于 2014-10-25 19:33:20

hyl1718 · 发表于 2014-10-27 10:06:22

x4412&ibox项目实战4－在uboot中添加开机LOGO

mzucore · 发表于 2014-10-27 10:15:41

牛~~~！！！

lzarhy · 发表于 2014-11-7 15:23:36

看看撒

wjl14090988 · 发表于 2014-11-13 21:53:45

正在做这相关的东西终于找到组织了谢谢了

bestrmb · 发表于 2014-11-21 14:40:34

ahaahahhhahhaahahaa

Beijixiong_433 · 发表于 2014-12-5 21:07:32

代码有点多······

Beijixiong_433 · 发表于 2014-12-7 11:14:57

貌似学到了点知识，继续加油！

mzucore · 发表于 2014-12-12 11:35:46

非常感谢您的分享~~~~~~~~

mobai · 发表于 2014-12-20 23:17:47

1111111111111111111111

hechuangm · 发表于 2015-2-17 02:44:53

谢谢分享！

1670739974 · 发表于 2015-3-2 23:56:27

kankan,欣赏

hotzwd · 发表于 2015-3-8 17:59:27

看看看看

北极冰晨123 · 发表于 2015-4-5 16:26:24

收下细读。

faichoi1427 · 发表于 2015-4-21 15:19:09

这个牛~~~

dydynfnf · 发表于 2015-5-1 20:20:44

牛厉害

piaoxueboy · 发表于 2015-5-13 12:09:01

学习一下，顺便做个标记

ocno · 发表于 2015-6-4 11:14:18

看看？~~~~~~~~~~~~~~~~~~

tcgoodboy · 发表于 2015-6-27 10:48:49

这个东西做出来效果应该不错。。。看一下

tcgoodboy · 发表于 2015-6-27 10:50:46

这个东西做出来效果应该不错。。。看一下