zImage 自己编译后刷到x210ii 无法开机是什么原因

jim · 发表于 2013-3-5 13:52:26

zImage 自己编译后刷到x210ii 无法开机是什么原因，SecureCRT 里信息有，屏幕黑的。

jim · 发表于 2013-3-5 13:54:56

而刷回光盘自带的 X210II_A\android2.3\image\inand\LCD070 下的uboot.bin zImage x210.img 正常启动。

armeasy · 发表于 2013-3-5 14:06:36

把打印信息贴上来

jim · 发表于 2013-3-5 14:11:08

[ 4.179684] <6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 4.186340] s5p-tvout s5p-tvout: hpd status is cable removed
[ 4.197338] Warning: unable to open an initial console.
[ 4.197439] Freeing init memory: 392K
[ 4.399133] DBUG_PORT must not use AFC!
[ 4.406289] init: cannot open '/initlogo.rle'
[ 4.444683] EXT4-fs (mmcblk0p2): recovery complete
[ 4.446399] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.449174] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.878094] EXT4-fs (mmcblk0p4): recovery complete
[ 4.879664] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[ 4.914361] EXT4-fs (mmcblk0p3): recovery complete
[ 4.916022] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 4.916727] EXT4-fs (mmcblk0p1): VFS: Can't find ext4 filesystem
[ 4.947782] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 4.994072] enabling adb
[ 4.994759] Enabled => usb_mass_storage
[ 4.994798] Enabled => adb
[ 5.015669] adb_open
[ 5.299640] PVR_K

Warning): SysFinalise: Version string: SGX540 S5PC110 [478, drivers/gpu/pvr/s5pc110/sysconfig.c]
/ # [ 5.535868] android_usb gadget: high speed config #1: Android Composite
[ 11.343750] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[ 11.769763] *** 12 BitS ***
[ 11.770445] s3c_sensor_open: ASIC revition ID : 1
[ 15.417346] request_suspend_state: wakeup (3->0) at 14913677294 (2010-02-03 09:36:34.756733834 UTC)
[ 15.744830] binder: release proc 179, transaction 607, not freed

jim · 发表于 2013-3-5 14:13:01

按一下power键SecureCRT中再出现如下信息：

/ # [  121.865750] request_suspend_state: sleep (0->3) at 121362171962 (2010-02-03 09:38:21.205227918 UTC)
[  121.866747] ==ft5x0x_ts_suspend=
[  125.223058] PM: Syncing filesystems ... done.
[  125.226970] Freezing user space processes ... (elapsed 0.01 seconds) done.
[  125.242033] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  125.257669] Suspending console(s) (use no_console_suspend to debug)

jim · 发表于 2013-3-5 14:14:06

屏幕应该是白屏，很多竖线那种。

jim · 发表于 2013-3-5 14:17:12

这是完整信息

[ 0.000000]    fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000]    DMA    : 0xff000000 - 0xffe00000 (  14 MB)
[ 0.000000]    vmalloc : 0xe0800000 - 0xfc000000 ( 440 MB)
[ 0.000000]    lowmem  : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000]    modules : 0xbf000000 - 0xc0000000 (  16 MB)
[ 0.000000]    .init : 0xc0008000 - 0xc006a000 ( 392 kB)
[ 0.000000]    .text : 0xc006a000 - 0xc065e000 (6096 kB)
[ 0.000000]    .data : 0xc065e000 - 0xc06b04a0 ( 330 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000]  RCU-based detection of stalled CPUs is disabled.
[ 0.000000]  Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:393
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2937815369]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.459851] Calibrating delay loop... 998.15 BogoMIPS (lpj=1949696)
[ 0.542900] pid_max: default: 32768 minimum: 301
[ 0.542994] Mount-cache hash table entries: 512
[ 0.543325] Initializing cgroup subsys debug
[ 0.543368] Initializing cgroup subsys cpuacct
[ 0.543410] Initializing cgroup subsys freezer
[ 0.545502] CPU: Testing write buffer coherency: ok
[ 0.552405] regulator: core version 0.5
[ 0.554273] NET: Registered protocol family 16
[ 0.564232] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.564809] pmstats at 00000000
[ 0.567968] Open OV2655 camema sensor
[ 0.707045] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.707130] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.707214] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.707420] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.714978] smdkv210_nand_io_init
[ 0.718708] S5PV210: Initializing architecture
[ 0.722995] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.731110] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
[ 0.739510] s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000, tin=divclk, base 12
[ 0.748001] s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000, tin=divclk, base 16
[ 0.756620] regulator: pd_audio_supply: 5000 mV normal
[ 0.761758] regulator: pd_cam_supply: 5000 mV normal
[ 0.766778] regulator: pd_tv_supply: 5000 mV normal
[ 0.771711] regulator: pd_lcd_supply: 5000 mV normal
[ 0.776745] regulator: pd_g3d_supply: 5000 mV normal
[ 0.781763] regulator: pd_mfc_supply: 5000 mV normal
[ 0.792476] bio: create slab <bio-0> at 0
[ 0.793107] SCSI subsystem initialized
[ 0.794536] usbcore: registered new interface driver usbfs
[ 0.799958] usbcore: registered new interface driver hub
[ 0.805253] usbcore: registered new device driver usb
[ 0.810586] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.815747] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.821117] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.826627] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.833029] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[ 0.839928] Bluetooth: Core ver 2.15
[ 0.843494] NET: Registered protocol family 31
[ 0.847883] Bluetooth: HCI device and connection manager initialized
[ 0.854210] Bluetooth: HCI socket layer initialized
[ 0.859301] cfg80211: Calling CRDA to update world regulatory domain
[ 0.865585] Switching to clocksource clock_source_systimer
[ 0.876084] NET: Registered protocol family 2
[ 0.876321] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.882856] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.889602] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.896356] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.902396] TCP reno registered
[ 0.905505] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.911426] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.917892] NET: Registered protocol family 1
[ 0.923691] PMU: registered new PMU device of type 0
[ 0.927065] wifi power management
[ 0.930685] SMDKC110/V210 RTC, (c) 2010 Samsung Electronics
[ 0.935978] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[ 0.942065] smdkc110-rtc smdkc110-rtc: rtc core: registered s3c as rtc0
[ 0.948551] S5PV210 ADC driver, (c) 2010 Samsung Electronics
[ 0.954345] cpuidle: phy_regs_save:0x4fd86000
[ 0.958782] input: s3c-button as /devices/virtual/input/input0
[ 0.964282] s3c button Initialized!!
[ 0.967954] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 0.972772]  DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[ 0.978900] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 0.983774]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.989912] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 0.994774]  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.007436] ashmem: initialized
[ 1.007730] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.008230] msgmni has been set to 630
[ 1.014552] alg: No test for stdrng (krng)
[ 1.016061] io scheduler noop registered
[ 1.019933] io scheduler deadline registered
[ 1.024163] io scheduler cfq registered (default)
[ 1.029717] s3cfb s3cfb: [fb2] dma: 0x475ab000, cpu: 0xe1000000, size: 0x00a00000
[ 1.044328] s3cfb s3cfb: registered successfully
[ 1.044373] Start display and show logo
[ 1.246119] ---x210_LED_init---
[ 1.313234] input: compass as /devices/virtual/input/input1
[ 1.314441] PA FB = 0x475AB000, bits per pixel = 32
[ 1.314488] screen width=1280 height=1024 va=0xd75ab000 pa=0x475ab000
[ 1.314545] xres_virtual = 1280, yres_virtual = 2048, xoffset = 0, yoffset = 0
[ 1.314986] fb_size=10485760
[ 1.317902] Back frameBuffer[0].VAddr=d7aab000 PAddr=47aab000 size=5242880
[ 1.325054] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 1.333219] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 1.341272] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 1.349371] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 1.361726] brd: module loaded
[ 1.363998] loop: module loaded
[ 1.364506] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.368946] Unknown NAND Device.
[ 1.372111] PPP generic driver version 2.4.2
[ 1.376561] PPP Deflate Compression module registered
[ 1.381307] PPP BSD Compression module registered
[ 1.386798] PPP MPPE Compression module registered
[ 1.390765] NET: Registered protocol family 24
[ 1.396633] dm9000 Ethernet Driver, V1.31
[ 1.400381] eth0: dm9000c at e0896300,e089a304 IRQ 42 MAC: 00:09:c0:ff:ec:48 (platform data)
[ 1.407633] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.414198] s5p-ehci s5p-ehci: s5pv210 EHCI
[ 1.418234] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.425326] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[ 1.441258] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.441851] hub 1-0:1.0: USB hub found
[ 1.441906] hub 1-0:1.0: 1 port detected
[ 1.443754] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.449807] s5p-ohci s5p-ohci: s5pv210 OHCI
[ 1.453852] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[ 1.460870] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
[ 1.523833] hub 2-0:1.0: USB hub found
[ 1.523880] hub 2-0:1.0: 1 port detected
[ 1.524168] Initializing USB Mass Storage driver...
[ 1.524317] usbcore: registered new interface driver usb-storage
[ 1.524369] USB Mass Storage support registered.
[ 1.524754] usbcore: registered new interface driver usbserial
[ 1.530456] usbserial: USB Serial Driver core
[ 1.534829] USB Serial support registered for GSM modem (1-port)
[ 1.540886] usbcore: registered new interface driver option
[ 1.546312] option: v0.7.2:USB Driver for GSM modems
[ 1.551372] s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
[ 1.551379] s3c-udc : version 15 March 2009 (DMA Mode)
[ 1.564775] android init
[ 1.567312] android_probe pdata: c066c240
[ 1.571330] android_bind
[ 1.573866] android_usb gadget: android_usb ready
[ 1.594683] f_acm init
[ 1.594707] android_register_function acm
[ 1.594742] f_adb init
[ 1.594765] android_register_function adb
[ 1.594800] f_mass_storage init
[ 1.594869] fsg_probe pdev: c066b0b8, pdata: c066c264
[ 1.599297] android_register_function usb_mass_storage
[ 1.604384] f_mtp init
[ 1.606704] android_register_function mtp
[ 1.610694] f_rndis init
[ 1.613281] android_register_function rndis
[ 1.617377] rndis_function_bind_config MAC: 02:02:45:46:4F:48
[ 1.623102] android_usb gadget: using random self ethernet address
[ 1.629253] android_usb gadget: using random host ethernet address

jim · 发表于 2013-3-5 14:18:52

[ 1.636225] usb0: MAC 96:93:44:b8:6b:ef
[ 1.639212] usb0: HOST MAC 5a:d0:c6:27:cb:5a
[ 1.643679] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.650305] android_usb gadget: Number of LUNs=1
[ 1.654887]  lun0: LUN: removable file: (no medium)
[ 1.659818] adb_bind_config
[ 1.663353] mtp_bind_config
[ 1.665784] mice: PS/2 mouse device common for all mice
[ 1.670806] S5P Touchscreen driver, (c) 2008 Samsung Electronics
[ 1.676585] s3c-ts s3c-ts: Created Mean filter len:2 coords:2
[ 1.682233] s3c-ts s3c-ts: Created Linear filter coords:2
[ 1.687578] s3c-ts s3c-ts: Created zoom filter coords:2
[ 1.692756] s3c-ts s3c-ts: 3 filter(s) initialized
[ 1.698590] S5P TouchScreen got loaded successfully : 12 bits
[ 1.703411] input: S5P TouchScreen as /devices/virtual/input/input2
[ 1.709814] Initial Goodix Touch Driver
[ 1.764182] input: goodix-ts as /devices/virtual/input/input3
[ 1.764564] goodix init panel config info fail
[ 1.764665] goodix-iic: probe of 1-0055 failed with error -1
[ 1.764779] s5pv210 ssd2531 Touch Driver
[ 1.764958] ##########ssd2531ts_probe##########
[ 1.766232] ##################### ak_i2c_probe: client = dfebb800
[ 1.772224] ** tea_dev_init_70HF **
[ 1.870947] usb 1-1: new high speed USB device using s5p-ehci and address 2
[ 1.903237] Device ID :0x38 0x7e
[ 1.903268] Warring! SSD touch device Not Found!
[ 1.903308] SSD Touch not found!
[ 1.903347] s3c-ssd2531-ts: probe of s3c-ssd2531-ts failed with error -12
[ 1.903437] ==ft5x0x_ts_init==
[ 1.913737] [FTS] ft5x0x_ts_probe, driver version is 2.0.
[ 1.914076] input: ft5x0x_ts as /devices/virtual/input/input4
[ 1.914310] ==register_early_suspend =
[ 1.916844] msg ft5x0x_i2c_rxdata i2c read error: -6
[ 1.921643] ft5x0x_read_data read_data i2c_rxdata failed: -6
[ 2.001917] hub 1-1:1.0: USB hub found
[ 2.002301] hub 1-1:1.0: 4 ports detected
[ 2.070659] [FTS] Firmware version = 0x11
[ 2.071200] [FTS] report rate is 80Hz.
[ 2.071737] [FTS] touch threshold is 108.
[ 2.072279] [FTS] ==probe over =
[ 2.072434] usbcore: registered new interface driver IRTOUCH
[ 2.072484] irtouch_dt: v1.0:IRTOUCH USB touchscreen driver
[ 2.074511] using rtc device, s3c, for alarms
[ 2.078813] i2c /dev entries driver
[ 2.082761] Linux video capture interface: v2.00
[ 2.087096] s3c-csis: Samsung MIPI-CSI2 driver probed successfully
[ 2.093102] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[ 2.093109]
[ 2.101692] S3C JPEG Driver, (c) 2007 Samsung Electronics
[ 2.106660] JPEG driver for S5PV210
[ 2.110726] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[ 2.116574] S5PC11X HPD Driver, (c) 2009 Samsung Electronics
[ 2.122374] S5PC11X CEC Driver, (c) 2009 Samsung Electronics
[ 2.130294] device-mapper: uevent: version 1.0.3
[ 2.135737] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 2.140865] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 2.146488] usbcore: registered new interface driver btusb
[ 2.151885] cpuidle: using governor ladder
[ 2.155960] cpuidle: using governor menu
[ 2.159830] sdhci: Secure Digital Host Controller Interface driver
[ 2.165943] sdhci: Copyright(c) Pierre Ossman
[ 2.170390] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[ 2.176858] android_usb gadget: high speed config #1: Android Composite
[ 2.183465] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
[ 2.190022] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[ 2.197022] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 2.203846] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[ 2.210389] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz)
[ 2.216978] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[ 2.252140] android_usb gadget: common->fsg is NULL in fsg_setup at 606
[ 2.252431] android_usb gadget: common->fsg is NULL in fsg_setup at 606
[ 2.253675] android_usb gadget: common->fsg is NULL in fsg_setup at 606
[ 2.295499] wifi power enabled
[ 2.295643] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 2.295750] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[ 2.295818] s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)
[ 2.296473] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[ 2.303362] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 2.310307] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[ 2.316860] s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)
[ 2.323443] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[ 2.330304] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 2.337548] usbcore: registered new interface driver usbkbd
[ 2.342753] usbkbd: :USB HID Boot Protocol keyboard driver
[ 2.348276] usbcore: registered new interface driver usbmouse
[ 2.353929] usbmouse: v1.6:USB HID Boot Protocol mouse driver
[ 2.360252] logger: created 64K log 'log_main'
[ 2.364208] logger: created 256K log 'log_events'
[ 2.368871] logger: created 64K log 'log_radio'
[ 2.373365] logger: created 64K log 'log_system'
[ 2.377963] timed-gpio: probe of timed-gpio failed with error -16
[ 2.386041] No device for DAI WM8976 HiFi
[ 2.387910] No device for DAI WM8888 HiFi
[ 2.392059] s3c64xx_iis_dai_init:s3c64xx-i2s0
[ 2.396437] s3c64xx_iis_dev_probe:id0 !!!
[ 2.400326] s3c64xx_iis_dai_init:s3c64xx-i2s1
[ 2.405001] WM8888 Audio Codec 0.4wm8888_probe: i2c_master_send
[ 2.410742] wm8888_init
[ 2.439488] mmc0: new high speed MMC card at address 0001
[ 2.439757] mmcblk0: mmc0:0001 NCard  3.71 GiB
[ 2.440037]  mmcblk0: p1 p2 p3 p4
[ 2.618341] android_usb gadget: high speed config #1: Android Composite
[ 3.185173] s3c_idma_preallocate_buffer:  VA-e0900000  PA-C0000000  163840bytes
[ 3.185511] s3c_preallocate_dma_buffer: VA-ff008000, PA-4FF40000, 131072bytes
[ 3.185572] asoc: WM8888 HiFi <-> s3c64xx-i2s0 mapping ok
[ 3.189289] WM8976 Audio Codec 0.4wm8976_probe: i2c_master_send
[ 3.189491] wm8976_init
[ 3.961976] s3c_preallocate_dma_buffer: VA-ff028000, PA-4FF60000, 131072bytes
[ 3.962276] s3c_preallocate_dma_buffer: VA-ff048000, PA-4FF80000, 131072bytes
[ 3.962338] asoc: WM8976 HiFi <-> s3c64xx-i2s1 mapping ok
[ 3.965675] ALSA device list:
[ 3.965708] #0: smdkc1000 (WM8888)
[ 3.965804] #1: smdkc1001 (WM8976)
[ 3.969409] GACT probability NOT on
[ 3.972848] Mirror/redirect action on
[ 3.976487] u32 classifier
[ 3.979149]    Actions configured
[ 3.982545] Netfilter messages via NETLINK v0.30.
[ 3.987285] nf_conntrack version 0.5.0 (5044 buckets, 20176 max)
[ 3.993385] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 4.000578] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 4.008473] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 4.015227] ctnetlink v0.93: registering with nfnetlink.
[ 4.020017] xt_time: kernel timezone is -0000
[ 4.026346] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.029625] arp_tables: (C) 2002 David S. Miller
[ 4.034188] TCP cubic registered
[ 4.037348] NET: Registered protocol family 10
[ 4.043559] lo: Disabled Privacy Extensions
[ 4.051899] Mobile IPv6
[ 4.051928] IPv6 over IPv4 tunneling driver
[ 4.054005] sit0: Disabled Privacy Extensions
[ 4.059741] ip6tnl0: Disabled Privacy Extensions
[ 4.062803] NET: Registered protocol family 17
[ 4.065830] NET: Registered protocol family 15
[ 4.070392] Bluetooth: L2CAP ver 2.14
[ 4.073875] Bluetooth: L2CAP socket layer initialized
[ 4.078926] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.083415] Bluetooth: SCO socket layer initialized
[ 4.088374] Bluetooth: RFCOMM TTY layer initialized
[ 4.093135] Bluetooth: RFCOMM socket layer initialized
[ 4.098241] Bluetooth: RFCOMM ver 1.11
[ 4.101957] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

armeasy · 发表于 2013-3-5 14:20:21

已经进系统了，估计你是不是改到LCD驱动了

jim · 发表于 2013-3-5 14:23:44

[  131.214646] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  131.230228] Suspending console(s) (use no_console_suspend to debug)
[  131.232418] alarm_suspend(dfec1400, 2)
[  131.232436] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  131.232455] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  131.232469] rtc alarm set at 1265269064, now 1265190008, rtc delta 1.200044291
[  131.232478] smdkc110_rtc_setalarm
[  131.232487] s3c_rtc_setalarm: 1, 04/01/110 07.37.44
[  131.232494] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  131.234403] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  131.249768] gpio_switch_suspend:close speaker amp power
[  131.254544] smdkc110_rtc_suspend
[  131.254755] PM: suspend of devices complete after 23.011 msecs
[  131.255116] s3c24xx_i2c_suspend_noirq
[  131.255123] s3c24xx_i2c_suspend_noirq
[  131.255129] s3c24xx_i2c_suspend_noirq
[  131.255153] PM: late suspend of devices complete after 0.386 msecs
[  131.255542] PM: early resume of devices complete after 0.328 msecs
[  131.256016] smdkc110_rtc_resume
[  131.257523] wakeup wake lock: event0-108
[  131.271937] usb usb1: root hub lost power or was reset
[  131.355658] usb usb2: root hub lost power or was reset
[  131.436475] DBUG_PORT must not use AFC!
[  131.510470] wifi power enabled
[  131.510492] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  131.648123] usb 1-1: reset high speed USB device using s5p-ehci and address 2
[  131.837945] android_usb gadget: high speed config #1: Android Composite
[  131.884046] alarm_resume(dfec1400)
[  131.884189] PM: resume of devices complete after 628.563 msecs
[  131.996700] Restarting tasks ...
[  132.001376] adb_release
[  132.012817] adb_open
[  132.013296] request_suspend_state: wakeup (3->0) at 131509803592 (2010-02-03 09:40:15.002773298 UTC)
[  132.052751] dai_active 0, IISMOD 00000100, IISCON 8050ce10
[  132.052810] Inside s5p_i2s_resume0..@735
[  132.072674] done.
[  132.074037] dai_active 0, IISMOD 00000000, IISCON 00000e00
[  132.076574] suspend: exit suspend, ret = 0 (2010-02-03 09:40:15.066053874 UTC)
[  132.076641] s3cfb_late_resume is called
[  132.378589] s3cfb_late_resume is complete
[  132.378642] sensor_i2c_resume
[  132.434202] ==ft5x0x_ts_resume=
[  137.071579] request_suspend_state: sleep (0->3) at 136568089879 (2010-02-03 09:40:20.061059543 UTC)
[  137.072582] ==ft5x0x_ts_suspend=
[  140.167985] PM: Syncing filesystems ... done.
[  140.168512] Freezing user space processes ... (elapsed 0.01 seconds) done.
[  140.183354] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  140.198939] Suspending console(s) (use no_console_suspend to debug)
[  140.201124] alarm_suspend(dfec1400, 2)
[  140.201142] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  140.201160] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  140.201174] rtc alarm set at 1265269065, now 1265190023, rtc delta 0.190654293
[  140.201184] smdkc110_rtc_setalarm
[  140.201193] s3c_rtc_setalarm: 1, 04/01/110 07.37.45
[  140.201200] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  140.203088] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  140.218469] gpio_switch_suspend:close speaker amp power
[  140.218754] smdkc110_rtc_suspend
[  140.218961] PM: suspend of devices complete after 18.529 msecs
[  140.219316] s3c24xx_i2c_suspend_noirq
[  140.219324] s3c24xx_i2c_suspend_noirq
[  140.219329] s3c24xx_i2c_suspend_noirq
[  140.219353] PM: late suspend of devices complete after 0.380 msecs
[  140.219737] PM: early resume of devices complete after 0.327 msecs
[  140.220013] smdkc110_rtc_resume
[  140.222309] wakeup wake lock: event0-108
[  140.235379] usb usb1: root hub lost power or was reset
[  140.320089] usb usb2: root hub lost power or was reset
[  140.405202] DBUG_PORT must not use AFC!
[  140.477643] wifi power enabled
[  140.477664] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[  140.612936] usb 1-1: reset high speed USB device using s5p-ehci and address 2
[  140.798160] android_usb gadget: high speed config #1: Android Composite
[  140.848863] alarm_resume(dfec1400)
[  140.849004] PM: resume of devices complete after 629.183 msecs
[  140.961503] Restarting tasks ...
[  140.966226] adb_release
[  140.982818] adb_open
[  140.983260] request_suspend_state: wakeup (3->0) at 140479815589 (2010-02-03 09:40:26.005566710 UTC)
[  141.014682] dai_active 0, IISMOD 00000100, IISCON 8050ce10
[  141.014741] Inside s5p_i2s_resume0..@735
[  141.017436] done.
[  141.018646] dai_active 0, IISMOD 00000000, IISCON 00000e00
[  141.019743] suspend: exit suspend, ret = 0 (2010-02-03 09:40:26.042051916 UTC)
[  141.019811] s3cfb_late_resume is called
[  141.327237] s3cfb_late_resume is complete
[  141.327299] sensor_i2c_resume
[  141.383286] ==ft5x0x_ts_resume=
[  146.071929] request_suspend_state: sleep (0->3) at 145568488587 (2010-02-03 09:40:31.094239167 UTC)
[  146.073055] ==ft5x0x_ts_suspend=
[  150.089009] PM: Syncing filesystems ... done.
[  150.089707] Freezing user space processes ... (elapsed 0.01 seconds) done.
[  150.105186] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  150.120773] Suspending console(s) (use no_console_suspend to debug)

jim · 发表于 2013-3-5 14:27:53

armeasy 发表于 2013-3-5 14:20
已经进系统了，估计你是不是改到LCD驱动了

没改过源码,是原来光盘中 X210II_A\android2.3\x210_android2.3.tar.bz2 所解压的。
我只对android.img.cpio 中的 init.rc 加了如下红色部分内容：
198 # gsensor
199    chmod 666 /dev/sensor
200    chmod 666 /dev/kxtf9_aot
201    chmod 666 /dev/s3c2410_serial0
202    chmod 666 /dev/s3c2410_serial1
203    chmod 666 /dev/s3c2410_serial2
204    chmod 666 /dev/s3c2410_serial3

jim · 发表于 2013-3-5 14:29:13

armeasy 发表于 2013-3-5 14:20
已经进系统了，估计你是不是改到LCD驱动了

我要怎么看是不是改到LCD驱动？

jim · 发表于 2013-3-5 16:31:08

怎么还是没人帮忙啊

jim · 发表于 2013-3-5 16:32:24

kernel下，进入x210/android_gingerbread_v10/android/kernel/arch/arm/mach-s5pv210  三总都编译，并刷过都白屏。
#define AT070TN92    1
#define VGA_800X600    2
#define VGA_1024X768 3
#define DISP_MODE    AT070TN92
//#define DISP_MODE    VGA_800X600
//#define DISP_MODE    VGA_1024X768