九鼎创展论坛

标题: x210V3开发板烧写光盘wince系统usb始终连接不上 [打印本页]
作者: fayjunyang    时间: 2017-2-23 20:51
标题: x210V3开发板烧写光盘wince系统usb始终连接不上
x210V3开发板烧写光盘wince系统usb始终连接不上，是什么原因。主要日志如下：
CAM_Init
CAM_Init
CAM_Init
[WAV:E] m_bEnableCodecMaster ==TRUE  CHANG TO false.  for WM8976      hehe!
[WAV] I2C OPEN : I2C2: SUCCESS
[WAV] ACTUAL I2C CLCOK SPEAD : 64 Khz
[IIC_IST:E] SLAVE(0xEC) DETECTION IS FAILED & RECOVERY STAGE
[WAV] IOCTL_I2C_GENERAL_READ ERROR: 31
[IIC_IST:E] SLAVE(0xEC) DETECTION IS FAILED & RECOVERY STAGE
[WAV] IOCTL_I2C_GENERAL_READ ERROR: 31
[IIC_IST:E] SLAVE(0xEC) DETECTION IS FAILED & RECOVERY STAGE
[WAV] IOCTL_I2C_GENERAL_READ ERROR: 31

[ch7026] CH7026_Init Failed..........
[WAV] ACTUAL I2C CLCOK SPEAD : 64 Khz
[WAV] OutNormalMode InterruptThread is created
[WAV] Init is::AttachDevice SUCCESS_FS:2000!!port :1
successful
CAM_Open
[CEC] DllEntry() : Process Attach
[CEC] CEC_Init()
Exception 'Data Abort' (4): Thread-Id=00dd0002(pth=9decda04), Proc-Id=00400002(pprc=830d9308) 'NK.EXE', VM-active=00400002(pprc=830d9308) 'NK.EXE'
PC=c059cecc(ndis.dll+0x0000cecc) RA=c059cec0(ndis.dll+0x0000cec0) SP=d240e39c, BVA=c1bf69d8
Exception 'Raised Exception' (-1): Thread-Id=00dd0002(pth=9decda04), Proc-Id=00400002(pprc=830d9308) 'NK.EXE', VM-active=00400002(pprc=830d9308) 'NK.EXE'
PC=c003bd00(k.coredll.dll+0x0001bd00) RA=8003a4c8(kernel.dll+0x000064c8) SP=d240dc38, BVA=ffffffff
UART3 Rx Tx Configured
[UART] DMA init CH:3
[UART] DMA init CH:2
 m_dwDevIndex == 2
[UART] DMA init CH:1
[SDMMCCh2] SDHCControllerIst - Card is Inserted!
[SDMMCCh2] Setting for 1 bit mode , Clock Rate = 100000 Hz
[SDMMCCh2] HandleErrors - ERR CMD:5 : If the card is not a SDIO, CMD 5 does not work in reason.
[SDMMCCh2] HandleErrors - ERR CMD:1 : If the card is not a MMC, CMD 1 does not work in reason.
CAM_Open
CAM_Open
[CAMIF] ++CameraHal::CameraInitialize(0)
[CAMIF] CAM_A_PORT

OV2655::GPH22 INIT  POWER OFF--------------------
[SDBUS] SD/SDHC supports the high-speed mode.
[SDMMCCh2] Setting for 4 bit mode , Clock Rate = 50000000 Hz
[CAMIF SetCamIFClockOn] ++CameraHal::SetCamIFClockOn(bOnOff=0) m_CamIrq = 107



!ModuleInit,g_selectedModule = 1
ModuleInit: OV2655()

OV2655::Init
[CAMIF] ++CameraHal::CameraInitialize(0)
[CAMIF] CAM_A_PORT

OV2655::GPH22 INIT  POWER OFF--------------------
[CAMIF SetCamIFClockOn] ++CameraHal::SetCamIFClockOn(bOnOff=0) m_CamIrq = 105



!ModuleInit,g_selectedModule = 1

OV2655::Init
[HDMI]++HDMI_initialize_register_address(0xb7700000,0xb7710000,0xb7710600)

STDA_interrupt_initialize_interrupt    pPMCtxt->bHPDStatus = (0)

[STDA_HDMI_HpdSetMode]  pPMCtxt->bHPDStatus = 0

++PHY_SetPowerDown
0x01
0x05 0x00 0xd8 0x10 0x1c 0x30 0x40 0x6b
0x10 0x02 0x52 0x1f 0x23 0x5b 0x7e 0x84
0x00 0x10 0x38 0x00 0x08 0x10 0xe0 0x22
0x40 0xf3 0x26 0x00 0x00 0x00 0x80
--PHY_SetPowerDown
[CMM] v_addr : 0xad480000 p_addr : 0x25480000 size : 0x004e0000 loc : 0
[IOCTL_CODEC_MEM_ALLOC] u_addr:0xd3490000  CallerProcessID : 0x400002
[MFC_DRV: WARNING] MfcFWBufMemMapping: virFWBuf : d3490000
[MFC_DRV: WARNING] MfcFWBufMemMapping: phyFWAddr : 25480000
[MFC_DRV: WARNING] MFC_Open: It is called by Power Manager
[MFC_DRV: WARNING] MFC_IOControl: POWER_CAPABILITIES : 0x11
MFC power on
[MFC_DRV: WARNING] MFCOpen++:

[MFC_DRV: WARNING] MFCOpen: FirmwareVersion : 00100407
[MFC_DRV: WARNING] MFC_Open(): Instance Number : 1

[MFC_DRV: WARNING] MFC_Open(): CLK_CNTL is enabled

[MFC_DRV: WARNING] MFC_Close(): MfcCtx->InstNo : 1

[MFC_DRV: WARNING] MFCClose:

[MFC_DRV: ERROR] WaitForDone: Interrupt :: MFC_R2H_CMD_ERR_RET(0x4)
[MFC_DRV: ERROR] MFCClose: closing is failed
MFC power off
[UFNPDD] USB_POWER : D0 IN
[UFNPDD] USB_POWER : D0 OUT
[UFNPDD] USB Serial Function Class Enabled
LayMgr.cpp: Layout Manager successfully initialized to  1
TOUCH FT5X06 INTERRUPT INIT!......................
[TOUCH] I2C OPEN : I2C1: SUCCESS
[TOUCH] ACTUAL I2C CLCOK SPEAD : 128 Khz

[9tripod] ft5x06  Firmware version  [0x11]......................

[9tripod] report rate is 80Hz.................

[9tripod] touch threshold is 108        .....................
TSP_GetSysIntrVal: --------------------
Maximum Allowed Error 7:
[BootCompleteApp] Boot Complete Event Occured
[UFNPDD] USB_POWER : D0 IN
[UFNPDD] USB_POWER : D0 OUT
MSIM: IM_ReadRegistry read KB 5
Explorer(V2.0) taskbar thread started.
[UFNPDD] OTG Cable Attached
[UFNPDD] RESET Again
[UFNPDD] RESET Again
AUTORAS:: Dialer notifies: [1] [Dialer Start]
Error from RasDial 608 0
Posting WM_NETCONNECT(FALSE) message, ErrorCode = 608(0x260)
AUTORAS:: Dialer notifies: [2] [Dialer Terminate]

e1.png (13.9 KB, 下载次数: 143)

CEC_Init驱动加载之后出错

CEC_Init驱动加载之后出错

e2.png (18.39 KB, 下载次数: 138)

usb连接出错

usb连接出错




欢迎光临 九鼎创展论坛 (http://bbs.9tripod.com/) Powered by Discuz! X3.2